ACTi E33 Manuál

Procházejte online nebo si stáhněte Manuál pro Bezpečnostní kamery ACTi E33. ACTi E33 Hardware manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - Bullet Camera Series

Bullet Camera Series Hardware Manual E31, E32, E33, E34 Ver. 2013/12/04

Strany 2 - Table of Contents

www.acti.com Hardware Manual 10 Installation Procedures Mount the Camera Using the Bundled Bracket 1. Mark the location of the t

Strany 3 - Appendix 34

www.acti.com Hardware Manual 11 4. Depending on how you want to install the camera, attach the camera to the bracket through one o

Strany 4 - Precautions

www.acti.com Hardware Manual 12 CAUTION: If the camera will be installed outdoors, be sure to waterproof the cable connection by

Strany 5

www.acti.com Hardware Manual 13 Other Mounting Options In areas with fierce weather conditions, the light bundled bracket can be re

Strany 6 - Safety Instructions

www.acti.com Hardware Manual 14 Waterproof Cable Installation The camera and the pre-installed network cable are resistant to salt

Strany 7 - Introduction

www.acti.com Hardware Manual 15 Step 1: Remove the Pre-installed Network Cable (“Pigtail”) 1. Loosen the three (3) screws to deta

Strany 8 - Package Contents

www.acti.com Hardware Manual 16 Step 2: Prepare the Conduit Gland and Flex Conduit 1. Disassemble the bundled conduit gland as sh

Strany 9 - Physical Description

www.acti.com Hardware Manual 17 4. Insert the sealing insert and attach it at the end of the flex conduit. Step 3: Instal

Strany 10 - Installation Procedures

www.acti.com Hardware Manual 18 3. Secure the clamping nut to the body. NOTE: Make sure the clamping nut is tight to avoid possib

Strany 11 - Hardware Manual

www.acti.com Hardware Manual 19 Replace the Pre-Installed Network Cable The pre-installed network cable comes with an Ethernet

Strany 12

www.acti.com Hardware Manual 2 Table of Contents Precautions 4 Safety Instructions ...

Strany 13 - Other Mounting Options

www.acti.com Hardware Manual 20 Step 1: Remove the Pre-installed Network Cable (“Pigtail”) 1. Loosen the three (3) screws to deta

Strany 14

www.acti.com Hardware Manual 21 Step 2: Install the New Ethernet Cable 1. Insert the new Ethernet cable through the sealing nut, c

Strany 15

www.acti.com Hardware Manual 22 5. Tighten the sealing nut. Make sure the rubber is tightly squeezed to avoid possible water leak.

Strany 16

www.acti.com Hardware Manual 23 Basic Connections To connect the camera, you need to prepare the following:  Power over Ethernet

Strany 17

www.acti.com Hardware Manual 24 Connecting Multiple Cameras To connect multiple cameras, use a PoE switch.

Strany 18

www.acti.com Hardware Manual 25 Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera

Strany 19

www.acti.com Hardware Manual 26 By double-clicking with the left mouse on the camera model, it is possible to automatically

Strany 20

www.acti.com Hardware Manual 27 Using the Default Camera IP Address If there is no DHCP server in the given network, the user may h

Strany 21

www.acti.com Hardware Manual 28 Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in

Strany 22

www.acti.com Hardware Manual 29 Access the Camera Now that the camera and the PC are both having their unique IP addresses and are

Strany 23 - Basic Connections

www.acti.com Hardware Manual 3 Other Adjustments and Accessories 32 Adjust the Viewing Angle ...

Strany 24 - Connecting Multiple Cameras

www.acti.com Hardware Manual 30 The following examples in this manual are based on Internet Explorer browser in order to cover all

Strany 25 - Accessing the Camera

www.acti.com Hardware Manual 31 To check the firmware version through the Web Configurator, access the Setup page and click System

Strany 26

www.acti.com Hardware Manual 32 Other Adjustments and Accessories Adjust the Viewing Angle 1. Open the front cover. 2. Attac

Strany 27 - 192.168.0.100

www.acti.com Hardware Manual 33 Attach the Sunshield The use of sunshield is optional if the camera will be installed indoors. Howe

Strany 28

www.acti.com Hardware Manual 34 Appendix How to Make an Ethernet Cable 1. Prepare the following tools:  Ethernet cable without c

Strany 29 - Access the Camera

www.acti.com Hardware Manual 4 Precautions Read these instructions You should read all the safety and operating instructions before

Strany 30 - Password: 123456

www.acti.com Hardware Manual 5 Federal Communications Commission Statement This equipment has been tested and found to comply with

Strany 31

www.acti.com Hardware Manual 6 Safety Instructions Don’t open the housing of the product Cleaning Disconnect this video product fr

Strany 32 - Adjust the Viewing Angle

www.acti.com Hardware Manual 7 Introduction List of Models This hardware manual contains the following models: E31 1MP Bullet with

Strany 33 - Attach the Sunshield

www.acti.com Hardware Manual 8 Package Contents Bullet Camera Sunshield Conduit Gland Mounting Screw Kit Sunshield Screw Kit Qu

Strany 34 - Appendix

www.acti.com Hardware Manual 9 Physical Description 1) Reset Button Use the Reset Button to reset the camera to its factory defa

Komentáře k této Příručce

Žádné komentáře