Acti Outdoor PTZ / Speed Dome (I9x) on Horizontal Pole Uživatelský manuál

2013/12/03 Outdoor PTZ Mounting on a Horizontal Pole Using Pendant Mount Installation Guide For Models: I93, I94, I95, I96, KCM-82

www.acti.comInstallation Guide 10 Step 5: Connect the Cables The camera itself is waterproof, however take note that the cable connections are not

www.acti.comInstallation Guide 11 How to Waterproof the Cable Using the Cable Gland 1. Prepare the following items: Cable Gland Gland Rubber Rin

www.acti.comInstallation Guide 12 4. Insert the Ethernet cable through the sealing rubber and claw. 5. Attach one (1) supplied rubber ring

www.acti.comInstallation Guide 13 7. Connect the Ethernet connector to the Ethernet port of the camera. 8. Insert the sealing rubber and claw i

www.acti.comInstallation Guide 14 10. If necessary, connect the colored wires to digital input or output (DI/DO) devices to trigger events or noti

www.acti.comInstallation Guide 15 How to Waterproof the Cable Using the Conduit Gland 1. Prepare the following items: Cable Gland Gland Rubber R

www.acti.comInstallation Guide 16 4. Insert the sealing rubber and attach it at the end of the flexible conduit. 5. Attach one (1) supplied

www.acti.comInstallation Guide 17 7. Connect the Ethernet connector to the Ethernet port of the camera. 8. Insert the sealing rubber into the c

www.acti.comInstallation Guide 18 10. If necessary, connect the colored wires to digital input or output (DI/DO) devices to trigger events or noti

www.acti.comInstallation Guide 19 Pole Mount with Pendant Mount and Junction Box Installation Procedures Perform the following procedures to insta

www.acti.comInstallation Guide 2 Table of Contents Mounting Solutions ... 3 Pole Mount wi

www.acti.comInstallation Guide 20 Step 1: Unpack the Camera NOTE: To avoid scratches or leaving fingerprints on the dome cover, it is recommended

www.acti.comInstallation Guide 21 4. Attach the camera cover. Align the cover screws to the screw holes on the camera (as marked on the illustrat

www.acti.comInstallation Guide 22 3. Remove the four (4) screws securing the side door. Step 3: Prepare for Waterproof Installation 1. Pr

www.acti.comInstallation Guide 23 Step 4: Prepare the Pole Mount Kit NOTE: Before installation, make sure that the ceiling can bear more than the

www.acti.comInstallation Guide 24 DISCLAIMER: The manufacturer will not be responsible for damage caused by water leak from incorrect cabling meth

www.acti.comInstallation Guide 25 8. Continuously turn the screw head clockwise to adjust the wire strap until it snugly fits the pole. Do the sa

www.acti.comInstallation Guide 26 Step 5: Install the Straight Tube Attach the straight tube onto the pole mount using the four (4) screws (includ

www.acti.comInstallation Guide 27 Step 6: Install the Camera 1. Insert the camera cables through the straight tube, extension tube (if any), and

www.acti.comInstallation Guide 28 Below is a sample installation.

www.acti.comInstallation Guide 29 Step 7: Connect the Cables From the junction box, perform the following: 1. Connect the bundled power adapter a

www.acti.comInstallation Guide 3 Mounting Solutions If the camera will be installed on a horizontal pole using pendant mount, consider the followi

www.acti.comInstallation Guide 30 5. Close the junction box door using the four (4) screws supplied with the junction box. 6. NOTE: Make sure

www.acti.comInstallation Guide 31 Appendices How to Install Extension Tubes If the Straight Tube is not long enough, add one or more extension tub

www.acti.comInstallation Guide 32 How to Use the Power Adapter (For I9x Models) 1. Slide the voltage switch to set the adapter voltage according

www.acti.comInstallation Guide 33 How to Attach the Safety Wire Strap (For I9x Models) Most of ACTi’s mounting accessories have a safety screw whe

www.acti.comInstallation Guide 34 4. Align the bigger end of the safety wire strap on the mounting solution and then tightly attach the screw to

www.acti.comInstallation Guide 35 Safety Information Read these instructions You should read all the safety and operating instructions before usin

www.acti.comInstallation Guide 36 Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to

www.acti.comInstallation Guide 4 Pole Mount with Pendant Mount Installation Procedures The camera body and cables are waterproof. However, when us

www.acti.comInstallation Guide 5 2. Carefully lift the camera cover and place it aside. NOTE: The cover is attached to the camera by a metallic w

www.acti.comInstallation Guide 6 Step 2: Attach the Pole Mount Kit NOTE: Before installation, make sure the horizontal pole can bear more than the

www.acti.comInstallation Guide 7 5. Continuously turn the screw head clockwise to adjust the wire strap until it snugly fits the pole. Do the sam

www.acti.comInstallation Guide 8 Step 4: Install the Camera 1. Insert the camera cables through the straight tube, extension tube (if any), and t

www.acti.comInstallation Guide 9 Below is a sample installation.